Pass4sure Cisco CCNP Exam 642-892 3.27 rapidshare
Pass4sure > Cisco > CCNP > Exam 642-892
Pass4sure 642-892 Exam Questions
*
Product Description
Exam Number/Code: 642-892
Exam Name: Composite
“Composite”, also known as 642-892 exam, is a Cisco certification. With the complete collection of questions and answers, Pass4sure has assembled to take you through 326 Q&As to your 642-892 Exam preparation. In the 642-892 exam resources, you will cover every field and category in CCNP helping to ready you for your successful Cisco Certification.
Free Demo Download
Pass4sure offers free demo for 642-892 exam (Composite). You can check out the interface, question quality and usability of our practice exams before you decide to buy it.
Exam Details
The Composite exam (642-892) is the quickest way for currently certified Cisco Certified Network Professionals (CCNP®) and Cisco Certified Design Professionals (CCDP®) to obtain recertification. The exam tests skills and knowledge pertaining to the Building Scalable Cisco Internetworks (BSCI) and Building Cisco Managed Switched Networks (BCMSN) courses. Composite may be taken to recertify CCNP and CCDP certifications; it may also be taken in place of the BSCI and BCMSN exams required for CCNP and CCDP certifications. Candidates must successfully pass both routing and switching subsections of the Composite exam to successfully pass the exam.
pass4sure * Questions and Answers : 326 Q&As
* Updated: October 24th , 2008
* Price: $119.99 $89.99
QUESTION 51
Which one of the following commands would configure EIGRP for IP on your Cisco
router?
A. ip eigrp routing
B. router eigrp process-id
C. ip eigrp autonomous-system-number
D. router eigrp autonomous-system-number
E. None of the above
Answer: D
Explanation:
Perform the following steps to configure EIGRP for IP:
Step 1 Enable EIGRP and define the autonomous system.
routerCK(config)#router eigrp autonomous-system-number
Step 2 Indicate which networks are part of the EIGRP autonomous system.
routerCK(config-router)#network network-number
Step 3 Define bandwidth of a link for the purposes of sending routing update traffic on
the link.
routerCK(config-if)#bandwidth kilobits. This step is optional.
The syntax for configuring variance on an EIGRP router is:
variance number
In the EIGRP command sequence above, what is the function of the number
variable?
A. It acts as a multiplier.
B. It defines the limit for how far the metrics can be separated.
C. It indicates how many paths can be used for load balancing.
D. It indicates how many paths can be used for unequal load balancing.
E. None of the above
Answer: A
Explanation:
Every routing protocol supports equal cost path load balancing. IGRP and EIGRP also
support unequal cost path load balancing, which is known as variance. The variance
number command instructs the router to include routes with a metric less than or equal to
number times the minimum metric route for that destination. Thus number is used as
multiplier, even though it defines a limit for the metrics. This limit is used for unequal
load balancing.
QUESTION 54
You are the network engineer at Certkiller . You want to configure EIGRP to run
across a 56 Kbps serial PPP link on the Certkiller network. You also want to ensure
the proper convergence of EIGRP routes.
What command should you issue on the serial interface?
A. bandwidth 56
B. bandwidth 56000
C. ip bandwidth-percent eigrp 1 56
D. ip bandwidth-percent eigrp 1 56000
E. None of the above
Answer: A
Explanation:
The bandwidth is a logical construct whose value can have wide-reaching implications on
the function of your network. It does not affect the actual speed of the link. In fact, it is
practical to configure the bandwidth command only on serial lines, where the speed of
the link will vary considerably. This command is useful for routing protocols that use
bandwidth as part of the metric. For serial interfaces, this value defaults to a full T1, so it
my appear to be a better link than what is actually being used.
Router (config) # interface S0
Router (config-if) # bandwidth speed-of-line
The bandwidth command is always specified in kbps.
EIGRP limits itself to 50 percent of the value specified in the
bandwidth command, or if the bandwidth command is not set, the interface defaults. If
you need to limit this percentage further, the upper limit that EIGRP uses can be stated as
a percentage of the bandwidth command.
The ip bandwidth-percent-eigrp command interacts with the bandwidth command on the
interface. You would use this command primarily because in your network, the
bandwidth command does not reflect the true speed of the link. The bandwidth command
might have been altered to manipulate the routing metric and path selection of a routing
protocol, such as IGRP or OSPF. It might be better to use other methods of controlling
the routing metric and return the bandwidth to a true value. Otherwise, the ip
bandwidth-percent eigrp command is available. It is possible to set a bandwidth percent
that is larger than the stated bandwidth. This is with the understanding that, although the
bandwidth might be stated to be 56 kbps, the link is in fact 256 kbps. The following
shows the structure of the ip bandwidth-percent eigrp command:
Router (config) #interface S0
Router (config-if) #ip bandwidth-percent eigrp autonomous-system-number percent
QUESTION 58
Your network consists of a router named R1 that’s configured
in a hub and spoke topology, supporting 24 remote office via a point-to-multipoint
Frame Relay EIGRP network deployment. The bandwidth command was not
manually entered on the frame relay main interface or the sub-interfaces. What is
the perceived bandwidth (as seen by the EIGRP process) of each Frame Relay
connection?
A. 64 kbps
B. 128 kbps
C. 1.544 Mbps
D. 1.536 Mbps
E. None of the above
Answer: A
Explanation:
The default bandwidth for all serial WAN interfaces is 1.544 Mbps. EIGRP by default
assumes the bandwidth of a serial interface is a full T1 (1.544 Mbps) if not specified.
This includes sub-interfaces. For multipoint frame relay interfaces, the perceived
bandwidth used by the IOS is taken from the configured bandwidth, divided by the
number of configured neighbors. Since there are 24 remote offices, there are 24
configured frame relay neighbors, so the bandwidth used by the IOS is the full T1
divided by 24, which is 64kbps.
more info:pass4sure 642-892
testking 642-892
http://www.ciscoexams.org
PassGuide CCNP Practice Test Questions
Posted in Practice Tests on October 25, 2008
PassGuide CCNP Practice Test Questions
2 Responses to “Pass4sure Cisco CCNP Exam 642-892 3.27 rapidshare”
i need that
I enjoyed this very much! Just charming! Your composing manner is pleasing and the way you managed the subject with grace is notable. I am intrigued, I presume you are an expert on this subject. I am subscribing to your updates from now on.
Leave a Reply